91 Astrovan Column Tilt Repair part (1 of 2)

ScottysDetailing
ScottysDetailing
4 мар. 2010 г.
9 мин. 4 с. 26 170 просмотров 17 30 4.8
how to fix a loose steering column on a chevy: dont worry it easy to do, and you can save $150.00 bucks doing it your self.

Комментарии:

ScottysDetailing: 26 дек. 2013 г.
Take to a machine shop and have it pressed back in. 
dgpnaples10: 26 дек. 2013 г.
Would you know how to re-install the upper shaft on a 86 G Body steering column. I watched your video to repair my tilt, but in the final step the steering shaft came out. So I am having trouble re-installing the steering column fork onto the steering upper shaft , which has the split spherical "ball" in its fork. I have tried several times and can't get the fork over the slots on the spherical ball. Any help would be asppreciated.
0001rockstar1: 26 сен. 2010 г.
Great video. I have to take apart a column at work and all the service literature isn't all as helpful as this video is. I was mainly consirded with the lock plate tool. How to use it and the purpose ( that ring). I see now and it makes sense now. Now I need to go to napa and get a steering wheel puller set with the pivot pin and lock plate pullers. Thank you.
john carter: 13 фев. 2013 г.
@scottysdetailing i have a 1988 astrovan,the turn signal is not workin,but the hazzard makes it blink...They say its the switch handle.!How much do u think is
Neil Carpenter: 5 июля 2010 г.
Thanks man, Ive been struggling with this for a while.
gandl2123: 2 янв. 2011 г.
One of the best videos I have ever seen on YouTube. Great job in explaining it. However, is it really necessary to pull the pins? It seems like last time I did this that I could get to all four with universal and did not have to remove the pins etc.... Tks
juantyra: 4 окт. 2010 г.
Great work! Wish you had shown info on steering wheel lock plate pin. Just bought an old 88 Chevy 2500 with bad key lock and the steering wheel would not lock. The ignition key lock has been replaced. The pin that slides up into the wheel lock plate was in backwards. I turned it around but it still will not lock and unlock properly at times. An internal cam or something pushes it up to lock position but I just have to depend on it sliding back down to unlock.
john carter: 13 фев. 2013 г.
The switch handle cause the guy says it could be it and he went to the junkyard to buy it but he says its $168
ScottysDetailing: 2 янв. 2011 г.
I don't think that there is enough room between the steering nuckle and the outer case. So you can try, but if you need to pull the pins you can rent the pivot pin tool @ Checker/Orileys for just a few bucks.
nwmod39: 2 нояб. 2012 г.
has anyone ever broke off the pivot pin tool inside the pin? i just got to them on mine and before i even get 3 turns into pulling it, the tool snaps, leaving the tiny piece in the threaded hole.
ScottysDetailing: 3 мая 2010 г.
i had someone that told me i couldn't do it, and thats all it took me to figure it out. the high low beam switch was the hard part for me.
Fass Strokaa: 8 сен. 2010 г.
Can't you tell me where to but that small special puller? Thanks you!!
MrGarcia389: 11 мар. 2010 г.
i had the same problem in my 89 camaro...thanks to you i could fix my steering wheel, you helped alot in this video... keep posting.
Scotty Kilmer 4 мар. 2014 г.
2 мин. 58 с. 37 518
hoohoohoblin 26 сен. 2013 г.
3 мин. 48 с. 5 825
SteeringColumnRepair 1 мая 2013 г.
5 мин. 55 с. 10 615
RyanLeeProductions 30 апр. 2013 г.
4 мин. 28 с. 10 428
hoohoohoblin 27 дек. 2012 г.
5 мин. 31 с. 23 205
hoohoohoblin 18 нояб. 2012 г.
11 мин. 51 с. 24 145
6speeddakota . 5 окт. 2012 г.
10 мин. 57 с. 198 798
personalfunfest 22 авг. 2012 г.
12 мин. 58 с. 44 424
EricTheCarGuy 19 авг. 2012 г.
32 мин. 41 с. 158 340
ScottysDetailing 17 июля 2012 г.
8 мин. 30 с. 13 953
farmboy30117 12 июля 2012 г.
8 мин. 21 с. 16 113
1Patient 2 июля 2012 г.
10 мин. 49 с. 37 694
Dadi Kaspar 30 мая 2012 г.
11 мин. 36 с. 144 506
ScottysDetailing 11 мая 2012 г.
9 мин. 50 с. 33 767
beltstowing 3 апр. 2012 г.
3 мин. 13 с. 16 380